Latex data sheet
Latex Data Sheet
Personal Precautions None
Environmental Precautions None
Store the product in a cool and dry place below 40"C (104"FJ.
Avoid exposure to direct sunlight or fluorescent lighting to prevent discoloration.
Do not store the product in a damp or high humid areas.
Exposure Controls N/A
Eye Protection N/A
Skin Protection N/A
Respiratory Protection N/A
Appearance Latex Sheets
Colour (optional) Yellow / Orange / Green / Pink / Blue / Violet/ Grey& etc.
Surface Finishing Smooth with lightly powdered
Boiling Point N/A
Vapour Pressure N/A
Solubility in Water Insoluble
Conditions to Avoid N/A
Materials to Avoid Material made of or containing transitional metal (example: Iron, Copper)
Hazardous Decomposition Products In fire, these product may produce black smoke
User should be aware tlat components used in making this product may cause allergic reactions to some individuals. As
with many substances that have t}te potential of becoming an antigen through extended contact, prolonged contact with
latex can result in the sensitization ofan individual to latex.
No known lrritancy, Carcinogenicity, Reproductive Toxicity, Teratogenicity or Mutagenicity anticipated.
This product does not pose any ecological hazards.
Hazard Designation : Non-Hazardous
Flash Point N/A
Auto Ignition Temperature N/A
Extinguishing Media Water, CO2, Foam or Powder
Fire Fighting Procedures and Personal Protection Use standard procedure for combustion material fires, including approved
self-contained breathing apparatus.
Fire and Explosion Hazards: No fire or explosion hazards are associated with this product
R-Deco provides the information and recommendations set forth herein in good faith but makes
no representation as to its comprehensiveness or accuracy. This document is intended only as a guide to the appropriate
precautionary handling, individuals who receive this information must make their own determination as to its suitability
of their purpose prior to use. In no event will R-Deco be responsible for the damages of any
nature whatsoever resulting from its use of or reliance upon information.
Latex Rubber is a natural product and when treated with care and the correct products, Latex Rubber garments will have a
long life with many years of enjoyment out of them.
Latex Rubber Garments should be washed in warm clean water with no soap or detergents. Carefully wipe off excess water
with a soft towel and leave to dry flat. Lightly dust with talc before putting away.
DO NOT attempt to tumble dry and definitely DO NOT iron or dry clean rubber garments.
The natural gloss on Latex Rubber can be enhanced by light polishing using a silicone based polish but we particularly recommend continued polishing for that manufacture guaranteed shine.
There are some important facts about Latex Rubber that you should know about in order to take care and get maximum enjoyment from wearing Latex Rubber.
- It is easier to put a tight latex garment on if the inside is first lightly dusted with talc and we advise wearing light cotton gloves to avoid possible marking and fingernail damage.
- Oils, greases and solvents destroy rubber so do not use any oil based lubricants or creams.
- The glossy surface of Latex Rubber can be permanently scratched if you attempt to polish it hard with a dry cloth so take care that your polishing cloth does not dry out when polishing.
- Latex Rubber can discolour, and eventually perish, if exposed to heat, sunlight and light with a high u.v. content. We recommend that, when not being worn, latex garments should be kept, lightly talced, in a black plastic bag in a dry cupboard or drawer. Do not store in damp conditions and do not leave on or near heaters.
- Keep away from naked flame and fires, latex rubber burns readily.
- Latex Rubber permanently stains brown in contact with copper, brass or bronze. Light colours can even stain brown when handled after handling copper coins, so take care to keep dirty, sweaty fingers away from your latex clothes.
Solvent based adhesives dry quickly but the solvent can cause the latex to curl up. They are highly inflammable and must be used in well-ventilated work areas. They generate a good bond with good water resistance.
- Wipe away excess powder
- Clean surfaces with water (for latex adhesives) or solvent (for rubber solution adhesives). Use solvent sparingly because it will distort sheet but will flatten out when evaporated
- Allow sheet to dry completely
- Apply thin layer of adhesive to both surfaces
- Allow the adhesive to dry completely and any distortion caused by solvent to disappear
- Join the surfaces and apply slight pressure
- Allow 24 hours for the bond to develop fully
The Information contained herein is based on the data available to us and is believed to be correct as of the time prepared, Robben-Deco makes no warranty, expressed or implied regarding the accuracy of these data.